Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: updated UserManual
Panel
titleUser Manual

...

ISE-NIN Manual 1.0.0-updated on 23Dec2022.pdf

Panel
titleFirmware Download

Release Date:

...

  30.Nov.2022

Release info: First RC 1.0.0 released incl. more Banks/Presets 

...

Device compatibly: DIY Version and prebuilt Version

RC1.0.0 ISE-NIN-30112022.zip

Benedek_bank.syx (for DIY Versions must be installed manually) 


for Installation help, please read below.


Expand
titleold versions

04.Nov.2022:  depracted

new beta including vintage presets

you need to reset preset banks and settings after uploading the new firmware in ISE-NIN.

ISENIN_1.0.2B.zip

if you still have the old beta, you have to install again both files with ST-link  and you need to reset preset banks and settings after uploading the new firmware in ISE-NIN.


08.Oct.2022 depracted

1.0b beta :  that’s an beta version, install both files on the devices, start with 1.0b1 and install 1.0b2

In this beta are no presets available !

ISENIN_1.0B_2.hex

ISENIN_1.0B_1.hex


September 2022 depracted

0.4/0.7 in current test for beta not released for customers (tested by Patrick)

...


Note

The DIY version uses the same firmware as the prebuilt versions.

Prebuilt Users can ignore the Firmware update mechanism at the moment , because the firmware is still the same and up to date. (22.Dec.2022)


On this Page are 3 Firmware installation guides described:

...

  1. for DIY builds which are on beta firmware empty ( First time installation for DIY Builds)
  2. for DIY builds which are empty ( First time Installation for DIY Builds)

...

  1. on beta firmware (deprecated due to RC release)
  2. Firmware Updates for Prebuilt Versions (not available yet - because we are still on RC 1.0.0)

1. First time firmware installation for DIY Builds

Instructions for Flashing

1.1 Connect STM LINK to the Motherboard with the ribbon cable from the programmer and connect the STlink programmer with your Mac or PC

1.2 Turn ISENIN on

1.3 Open STM Cube Programmer  or ST LINK utility (cube programmer is the latest software, but STlink utility is fine too and often better)

1.4 Select ST-Link, select connect (which reads the ISE-NIN uC memory)

1.5 Select erasing and programming button (in STlink utility its "program & verify)

1.6 Browse select ISENIN 1.0.0_1.hex file from your pc/Mac. -   Start programming ***


1.7Repeat the procedure described above and select ISENIN 1.0.0_2hex    Start programming as before (program and verify)

***you don't need to restart the ISE-NIN after first programming step, in case the ST-LINK tool hangs, just reconnect the USB cable.

1.8 Disconnect and restart ISE-NIN its important to remove the Programmer from the ribbon cable - or the device will not start !! 


1.9  Start ISE-NIN and go in the ISE-NIN Menu and perform "reset all settings", otherwise some functions doesn't work.

(do not miss to run the calibration procedure which is described in the ISE-NIN Build guide


1.10 Now install /send by USB-MIDI with a sysex tool (sysex librian or other) the above Benedek.sysex file otherwise is the Benedek bank still empty. read step 1.11 !!!!


1.11 perform again a reset all settings and reboot the ISE-NIN after you sent the sysex file, or it can happen that bank is still empty.

there no receiving info on the synth when you send the sysex file to the synth.


2. DIY builds which are on beta firmware : (depracated)

Expand

...

2.1 you can use the CubeProgrammer and choose USB instead of STlink. - with following steps:

   

...

 2.1.1  press the SHIFT button on ISE-NIN while powering on the device, the OLED shows "DFU mode", (note: windows users have to reboot the PC or windows can’t recognize the DFU-mode)

   

...

 2.1.2 on the right upper side in CubeProg. app. choose "USB" and press "Connect"

           Image Modified 

   

   

...

 2.1.3 it must be shown as this result...         

             Image Modified

...

2.1.4 then choose on left hand the functions to upload the 1.0.0_1.hex - it disconnects after programming, 

...

2.1.5 restart ISE-NIN with shift button again and upload 1.0.0.2_hex and done..

...

2.1.6 ISE-NIN  restarts with 1.0.0 in the OLED boot sequence.

...

2.1.7 go in the menu settings in ISE.NIN and proceed a "reset settings".

Don´t forget to upload the additional bank as listed above. (USBMIDI with sysexlib tool etc.) and proceed a "reset settings" again and reboot ISE-NIN


you have to install both files, the first file can be uploaded and cube programmer disconnects with an error - normal

...


3.

...

Firmware

...

update for rebuild versions:

not available yet- no new FW. released yet (current Version is RC.1.0.0) valid until this page is updated


Changelog: (of this page)

...