This page is only for me 
i dont support Main Power handling (ich supporte keine 110V/230V Basteleien)
in case of usage of 110V/230V powersupplys dont add the parts for the onboard regulator (TTSH rev.1+2)
...
use rubber feeds otherwise the case "swings with the transformer frequency", you can hear it in the big ttsh case like a speaker.
tip: by usage of a internal 110V/230V psu - mount the psu in left corner and reverb tank on right/top corner with in/outputs to top - or you get a massive hum in reverb.
mount the psu on plastic/rubbers - because the empty case amplified the psu noise/hum/vibration.
| Info | ||
|---|---|---|
| ||
(if you have added the both switched regulators, desolder the 220nF caps, 100uH caps) |
For new build: (rev.2 aka 7.x pcb version)
- dont add the inductors, 47uf cap, 240R, 2k4, 4n7caps, 27k, voltage regulators, trimmer
- you only need to add: 3pin MTA156 header, run wires between TP3 and +15V and a Tp1 and -15V (see picture), (otherwise the Fader LEDs dont do his job )
for condor/powerone hbb1.5 powersupplys:
...
recalibrate your VCO V/oct and VCF 1V/oct if needed.
for condor/powerone haa0.8
only the transformer input 1+4 or 1+5 (for 230V) bridge the 2+3 pin, no trimming needed, measure the output
| Tip |
|---|
the usage of rubber feets minimize some vibrations from the transformer. mount the reverb tank at top with in/output orientation at top or you get some hum from the PSU. mount the PSU only on the left case side - on the right side is the reverb input and its very sensitive of magnetic fields. |
Altitude´s PSU:
https://www.muffwiggler.com/forum/viewtopic.php?t=130814&postdays=0&postorder=asc&start=0
...
dont forget to buy the Toroid https://www.digikey.de/product-detail/de/talema-group-llc/70083K/1295-1014-ND/3881427 Talema 70083K
| Qty3 | Value | Device | Package | Parts | Description | Digikey | Price (USD) | Ext. Price | |
| 1 | KK-156-2 | KK-156-2 | AC | 156 HEADER | A1971-ND | 0.19 | 0.19 | ||
| 1 | 2KBP | 2KBP | B1 | RECTIFIER | 2KBP10M-E4/51GI-ND | 0.78 | 0.78 | ||
| 6 | 3300 uF | CPOL-USE7.5-16 | E7,5-16 | C1, C3, C4, C5, C6, C7 | POLARIZED CAPACITOR | 565-2000-ND | 2.06 | 12.36 | |
| 2 | 0.1 uF | C-US025-024X044 | C025-024X044 | C2, C10 | CAPACITOR Ceramic | BC1148CT-ND | 0.44 | 0.88 | |
| 2 | 1 uF | CPOL-EUE2.5-6 | E2,5-6 | C8, C12 | POLARIZED CAPACITOR | 493-12827-1-ND | 0.25 | 0.5 | |
| 2 | 10 uF | CPOL-EUE2.5-6 | E2,5-6 | C9, C11 | POLARIZED CAPACITOR | 493-1144-ND | 0.22 | 0.44 | |
| 2 | 240R | R-US_0204/7 | 7/1/0204 | R5, R7 | RESISTOR | 237XBK-ND | 0.1 | 0.2 | |
| 2 | 1K | R-US_0204/7 | 7/1/0204 | R4, R6 | RESISTOR | 1.00KXBK-ND | 0.1 | 0.2 | |
| 2 | 10K | R-US_0204/7 | 7/1/0204 | R3, R8 | RESISTOR | 10.0KXBK-ND | 0.1 | 0.2 | |
| 2 | 2K | 3386-W | 3386W | R1, R2 | Timmer PV36W | 490-2880-ND | 1.51 | 3.02 | |
| 4 | 1N4002 | DIODE-D-7.5 | D-7.5 | D1, D2, D5, D6 | DIODE | 1N4002-TPMSCT-ND | 0.11 | 0.44 | |
| 2 | 2AMP | TR5 | TR5 | F1, F2 | FUSE | WK4257BK-ND | 0.7 | 1.4 | |
| 1 | MTA04-156 | J1 | 156 4 pin Header | A1972-ND | 0.2 | 0.2 | |||
| 1 | MTA03-100 | J2 | 100 3 pin header | A19470-ND | 0.2 | 0.2 | |||
| 2 | 529XXXXXXXX | 529XXXXXXXX | 529XXXXXXXX | KK1, KK2 | HEATSINK TO-220/218 | HS350-ND | 1.43 | 2.86 | |
| 2 | LED3MM | LED3MM | LED1, LED3 | LED | 160-1142-ND | 0.33 | 0.66 | ||
| 1 | L01-50VA | L01-50VA | L01-50VA | TR1 | TOROID TRANSFORMER | 1295-1014-ND | 39.58 | 39.58 | |
| 1 | V80212MS02Q | V80212MS02Q | V80212MS02Q | U$5 | Voltage Select Switch | CKC3001-ND | 4.09 | 4.09 | |
| 1 | LM317 | LM317TS | 317TS | U1 | VOLTAGE REGULATOR | LM317TFS-ND | 0.71 | 0.71 | |
| 1 | LM337 | LM337TS | 337TS | U2 | VOLTAGE REGULATOR | LM337TFS-ND | 0.71 | 0.71 | |
| Total | 68.91 |
Gallery
no earth wiring for TTSH in Picture 1, but its needed for powerone psus.
| Gallery |
|---|