You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 11 Next »

TTSH rev.3 build Power wiring TTSH rev.3 Pictures BOM TTSH Rev.3 known Issues TTSH Rev.3 Hardcore builders guide Modifications

Unable to render {include} The included page could not be found.

see Speaker wiring here

Power wiring for TTSH rev.3



This page contains hi-res pictures of the build process. More will be added while build continues ...

shared by Björn Verbruggen and me.


for more details click on the picture, please respect the copyright - please ask before share on other websites, for private usage only.

Unpopulated PCB Pictures

(download the picture and open it local)

PSU

 

You should bridge the connections for the choke, and reverse the dc in connector. (notice this is another connector, not the one stated in the BOM)

Mainboard

Preamplifier/ Ringmod

VCO-1

VCO-2

VCO-3

VCO4027

VCF/Mixer

ADSR/AR

VCA

Mixer

Reverb

Amplifiers

 

S/H


Voltage Processor

Noise

Filtercards

4012 Filter

 

Notice the LM301 is soldered directly to the pcb. However you should use IC sockets.

There are 2 things to keep in mind:

  • The BC558B needs to be mounted backwards (flat side of the transistor faces round side of the pcb print):

  • You have to swap 2 pins of the 3958 - use insulation:


4072 Filtercard






Synthcube left fullkits and partial kits

 

 BOM as Excellist:

 BOM-list-TTSH REV8-v1.3.xlsx   (the lists includes all parts. (update 18.january 2017 approved section added)

 

The shared mouser basket from thehumancomparator is wrong (22.Dec.2016)
(this Mouser basket was provided in the 'order' eMail)


https://www.mouser.de/ProjectManager/ProjectDetail.aspx?AccessID=234c0 9ed60   old  link from Jon

http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=6CEDD31990  new Mouser link from me, improved see notice field for quantity "order 10"


order the 100K resistors, 2N3906, 2N3904, 1N4148 from a local dealer to save money, make sure the 2N3904/2N3904 is from tape - for better transistor value matching.

dont miss to order the parts for the gatebooster too.
 


ttshv2BOM.pdf (mainboard pcb)  - i update the list in next 2 days. (remove the above listed SMT chokes and replace with chokes from SecondFilter_BOM)

4027v2BOM.pdf (vco boards)

TTSHrev3_SecondFilter_BOMv1.1.pdf (filter board)  please use matched pairs 4 pairs of 2N5087 and only matched pairs for 2N3906/2N3904 (exept the single trannys)


for the rare parts, please check thonk.co.uk or my own page ( i offer 2N5087 matched pairs too)

if you need matched pair trannys or single tested trannys like 2N3954/8 or others, please contact me.

further i offer a survival kit


dont miss to order (if you only use the mouser basket)

Speakers: Visaton SC8 (reichelt.de, tme.eu)

reverb tank https://www.banzaimusic.com/Belton-RBL2AB3C1B.html  see known issues for wiring 

RCA/Chinch cable 0,5m - 1m (double or triple isolated/shielded otherwise you gets hum issues)

DC Powersupply  12V DC/1,5A - 24V/1A DC works, middle pin is + (5,5mm/2,1mm size)

Cable for Power wiring and Speaker wiring (1mm² diameter for power, 0,5mm² for speaker)

13 x 12mm Spacer M3, black flat Screws for frontpanel, screws for speaker at the rear and spacermounting, washers, nuts, cable shrink, silicon for matched pairs or glue the trannys together

1 x 10mm spacer + washer for filtercard mounting (ignore the second hole for a spacer in VCF section)

 3x long spacers to mount the powersupply  (25mm-50mm preferred to minimize the risk of EMV issues )

 

as stated above, the project is NOT for beginners

nearly all professional builders have standard resistor and capacitor values at home (if the BOM miss a few standard parts like a 100K resistor)

 

 

 

use 3x 20k or 25k multiturn trimmer http://www.tme.eu/de/details/3339p-1-203lf/tht-potentiometer-mehrere-umdreh-516/bourns/ for V/OCT trimmer in the VCOs, this type works as a drop in replacement and gives you more room for a better calibration.

(there´s no need to mount it from the component pcb side as standard multiturn trimmer due to issues with the sizing behind the panel and pcb)

 

In TTSH V2 and V3, you can easily modify the LED system so as to trim the LEDs all the way of off. Replace the 3k3 resistor located next to the TL071 pads to a jumper.  Tested by fuzzbass - thank you.

 

 

  1. Major Bug: Description:  at the Frontpanel pcb side you find some "VIAs", at the VCO 3 section the jack S/H , VCO2 section the jack ADSR, VCA section the jack Ringmod, has a via with 15V, the metalcase of the jack is connected to ground and you run in a short between ground from the jack and 15V from the via, there are 2-4 other jacks with vias too.
    check each pcb installation site for VIAs before mounting the jacks.
    Solution:  file down the jack at the position of the via (1mm is fine) or cut it down
     

  2. Improvement: Powersupply Board - turn the 2pol MTA156 header if needed - otherwise the power input cable is above the powersupply.   (tick) confirmed, its not in every use case needed

  3. Minor Bug:Main board – Missing trace from V- to header. (copyright of picture for thehumancomparator.net ) (tick) confirmed


  4. Minor Bug: 4072 VCF missing trace pin 4 on LM1458 to -14V (use shrink tube for isolation) (tick) confirmed


  5. Minor Bug: 4012 VCF Board — BC558 must be installed backwards, schematics show Ermitter to 23k2 resistor in rev.7.2 (v2) (tick) confirmed


  6. Minor Bug: for all 2N3958 and 2N3954 change 2 pins like this,  cross the both pins - use shrink tubing for one pin for isolation. (tick) confirmed


  7. Improvement for build: or the Filtercards use flat electrolyte capacitors, check the height of all parts - if needed use other headers, check this for both Filtercards before you solder the headers, if needed place the 47pf(50pf) MLCC capacitor (on the mainboard) on solderside of the pcb)
    on my first build i used a 10mm spacer but i prefer the usage of 12mm spacers,  (by usage of 2 spacers - its needed to cut on the VCF out jack at the bottom some metal and you need a flat screw,  in result one spacer is enough  (wink) )


  8. Minor Bug: by usage of the banzai reverb tank, run in the reverb tank a wire from ground to ground on the RCA connectors to ground output and input

  9. Minor Bug: turn 180degrees on the mainboard the 5pol MTA156 power header, otherwise the power cable is to the wrong side and maybe you run in trouble with your case/cabinet size.

    the picture shows the correct mounting:

  10. Minor Bug/improvement: use a BC337-16 instead 2N5172 in the noise section more Details here (you don't need further mods)


11. Medium bug - the Clock LED driver (BC337) becomes hot - affect the functionality in some cases.

change the LED driver resistor LED-R17 from 220R to 1K ( its located at the Solderside bottom right, near the Clock fader)

        

12. Minor Bug -  the RCA connectors silkscreen on Mainboard is labeled wrong,  turn Input and Output RCA connectors  (red and white or (black) in same color as your reverb RCA connector color.


thanks to Anthony A Flagg for sharing the BOM and quick build guide

 

V3 quick build bom.xlsx 

 

 

  • No labels