Versions Compared


  • This line was added.
  • This line was removed.
  • Formatting was changed.

Projecttitel: ISE-NIN


Startdate: 26th Aug.2022

Duedate: 15th Sep.2022

Last page update:


26.Feb.2023 BOM corrected

Manufacture link:


Facebook Build Group: 

Facebook User Group:

Gearspace :

Table of Contents



Before you built the ISE-NIN kit:

  1. You need experience in soldering SMT Parts (around 350 SMT capacitors and 32 ICs in SOIC format).
  2. required Tools are: Soldering Station, Flux pen, magnifying Glasses, Oscilloscope, some pliers, tweezers, PC or Mac for installation of the boot loader and firmware
  3. It is recommended to have a bench- power supply with current limiter for the first test.
  4. Programming is done via an ST-link programmer which is listed in the BOM (former DDRM builders can use the existing programmer) - normally its a Windows App. but with some experience in MacOS possible too




ISE-NIN-BOM-REV1.0.4.xlsx      uploaded 26.Feb.2022 (PSU alternativ part was swapped in line 198/199)

ISE-NIN-BOM-REV1.0.3.xlsx uploaded 10.Dec.2022

ISE-NIN-BOM-REV1.0.2.xlsx uploaded 24.Nov.2022

ISE-NIN-BOM-REV1.0.1.xlsx   updated by BC on 24th.Sep.2022


Important Information before you start assembling:

Info ID






113. Aug.2022Hardware BoardINFO

minimize Slider/Potentiometer malfunctions

Soldering Info

when you install the sliders, DO NOT solder all pins successively, 

solder only one pin at the top and the bottom and proceed to the next slider, when you have installed all of them -  solder the next single pin of each slider.

this has to be respected with potentiometers too.

The Sliders and Potentiometers have lubrication inside which is sensitive to heat and can be easily damaged (this mistake was made in  many Syncussion clones ) 

213. Aug.2022Hardware BoardINFO

OLED Selection and R101/R32 - R100/R102

Image Modified

when you have an OLED with the PINOUT: VCC-GND-SCL-SDA install R100 and R102 (0 Ohm - a bridge) (R32/R101 must be left empty)

in case you have an OLED with the PINOUT: GND-VCC-SCL-SDA install R101 and R32 (0 Ohm -a bridge)

313. Aug. 2022All pcbsINFOsome IC Sockets do not point in the same direction as the others, it´s a known issue that people install ICs backwards Double and triple check every IC orientation -  maybe 80% of all device malfunctions happen because of that and often end in very expensive repairs
413. Aug.2022Hardware Board, PSU, MainboardINFOthe LEDs do not work

when you build the device - its important to start with the power supply - here you can test the LED orientation.

never trust the vendor pinout for LEDs. normally the long LED leg is the positive end (anode)

(but some circuits are powered from negative rails and GND is the positive end in this case- just as an explanation)

513. Aug. 2022MainboardINFO

solder the pins on the Edgecard holder where you find the white stripe on the PCB - 

Image Modified

you can't install the edge cards in the wrong way
614.Aug.2022MainboardINFOkeep the length of the power cable as short as possible - that minimizes the risk that you accidentally put the PSU card in a voice card slot

714.Aug.2022Hardware BoardINFOpay attention to "Pot23 - Volume" (upper right corner) this is the one non-center detent pot.


BOM1.0 Change- fixed in BOM v1.0.1

R103, R104, R105 = 330K (was 30k in BOM rev 1.0.0)

R128, R143 = 10K (was 30k in BOM rev1.0.0)

R137, R146 = 10K.  (was 20k in BOM rev1.0.0)

Image ModifiedImage Modified

fixed on 24.Sep.2022 in BOM 1.0.1
903.Oct.2022PartsINFOthe 2N3094 on the Voicecards must be a matched pair (within 2mV vbe)

A. if you are a pro builder.. you still have a device to match trannys.

B. you can order or build a tester

C. you order matched pairs by me or thonk


1018 April 2023PSU BUGR8 220R on the PSU goes very hot - it affect the lifetime of this part

workaround: change to 2Watt 220R 1% resistor metalfilm

or try 470R 0,6watt 1% metalfilm

a solution or other workaround is in test (TL431 source from the 5V regulator instead from 15v)

PCB Scan Pictures (thanks Janne.I)


titleResonance Calibration

Here is a step by step guide to calibrate the filter resonance: (ONLY AFTER that you need to calibrate filters in further step)

It´s recommend turning the resonance trimmer TR1 fully clockwise on each voicecard to make this procedure as easy as possible!

The best way is to use 8 resistors on the mainboard for making a measurement.

1. Warm up your unit about 30-40 mins

2. turn on ISE-NIN, Go to menu (press shift (grey cap button) + Back (middle button under the display), then calibration, choose resonanceCROSSMOD then press SHIFT and press the encoder, this will add the hidden RESONANCE and CROSSMOD TRIM function (its hidden since prebuilt units do not need this) (The display should read: "card 1" and you should hear a test tone through the outputs (for the next voice card you can press the "next (Back)" button to cycle through the voice cards)

3. Connect a Scope probe on the Mainboard, to the resistor of the card which you calibrate , set your oscilloscope to "timebase 0.5ms/cm" and "1V/cm" (on DMM: 0.5V -1V is fine too, depends on your scope screen resolution - some new scopes are HD resolution in 720p or more and the ADC are very accurat)

4. You should see the filter signal on your scope. If you have turned the trimmer fully clockwise the signal should be- and sound distorted. now turn the "resonance" trimmer TR1 on the Voicecard anti- clockwise until you get a clean signal as in the picture below (The difference of maximum and minimum amplitude in one cycle has to be 4-times.)

make sure to have enough gain otherwise the Filter calibration step will fail as described in next section.

Comment from Black Corp: "We especially made all settings in resonanse calibration how they should be (square, cutoff, 12db etc)."

Congratulations, you have successfilly calibrated the filter resonance for all of the voices!

Resonance calibration Method according to the Roland Jupiter-8 service manual (not recommended yet → use above method!!!):


Follow these steps from the Jupiter 8 manual, turning Trim1 for each voice (or see below):


or turn Trim TR1 until the self oscillation is off on each voice.

you can switch between the cards using the switch button on the mother board. 


title Cross Mod TRIM Calibration

MENU, CALIBRATION, choose CROSSMOD then press SHIFT and press the encoder, this will add the hidden RESONANCE and CROSSMOD TRIM function (its hidden since prebuilt units do not need this)CROSS MOD TRIM, connect USB out of ISENIN to computer, turn on ableton select ise-nin as input, put a tuner oh the channel and adjust it to 220hz with the Offset Trimmer for each voice, switch between voices with the switch button.