Date: Thu, 28 Mar 2024 23:51:20 +0100 (CET) Message-ID: <634665529.548.1711666280967@isp.rootgemeinschaft.de> Subject: Exported From Confluence MIME-Version: 1.0 Content-Type: multipart/related; boundary="----=_Part_547_549267387.1711666280966" ------=_Part_547_549267387.1711666280966 Content-Type: text/html; charset=UTF-8 Content-Transfer-Encoding: quoted-printable Content-Location: file:///C:/exported.html
http://www.florian-anwander.de/roland_system7= 00/
VCO: 702_a3.jpg.pdf
This Pages are just Infos for myself:
VCO
Pin out van de FET niet correct, nieuwe FET gemonteerd.
R30 ontbrak, in de documentatie met modificaties zou dit een 2k2 weersta= nd zijn. 10K weer-
stand op de onderkant van de print gemonteerd. Printspoor onderbroken. O= ntbrekende 820
ohm weerstand gemonteerd. R48 is op pcb gemarkeerd als 100k, moet 10k zi= jn.
Weerstand in het pulse breedte circuit ontbrak. 56K weerstand in plaats = van 560K ge-
monteerd. Jumper bij pwm input verbind de input met ground. Jumper verwi= jderd.
Weerstand tussen tune trimmer en cv summer ontbrak. 100K weerstand gemon= teerd op
onderkant print. VCO 2 was instabiel door een probleem met de THAT300 tr= ansistor array.
Transistor array vefvangen. Ua726 niet af te regelen op 50 graden, diver= se tests gedaan,
heater kan niet genoeg warmte genereren om tot 50 graden te komen. Maxim= aal 43 graden
was haalbaar in testopstelling. Afgeregeld op 38 graden.
VCF #1
Header voeding zat niet goed g= esoldeerd, header verwijderd. Gaten opgeboord ennieuwe header gemonteerd. Elektrolytische condensator zat verkeerd om ge= monteerd.
Ingang van de sommeerversteker van de control voltages zat niet aangeslo= ten.
Transistoren Q1 en Q2 staan verkeerd om op de print. Transistoren gewiss= eld.
Weerstand van 10ohm in plaats van 10Mohm in de aansturing van de OTA's. = Weerstanden
van 10k vervangen door 22k in de aansturing van de OTA's. Meegeleverde C= A3080 werken niet. Nieuwe CA3080's geplaatst.
Keramische condensatoren in het filter vervangen door polystyreen conden= satoren.
1PF condensatoren rond de buffers vervangen en LM301's vervangen door CA= 3140's.
Extra uitgang voor BPF en HPF gemaakt. Weerstand vervangen. 12NF vervang= en door 15nF.
1 verkeerde weerstand in het overload circuit, 4R7 in plaats van 4M7. El= co verkeerd om, staat
verkeerd op de print. Overload werkte niet doordat de ingang van de over= load detector ver-
bonden was met V+. Printspoor onderbroken.
Sample&hold
Condensatoren verkeerd om gemonteerd, staat niet goed aangegeven op de p= rint! PNP tran-
sistor als Q4 gemonteerd moet een NPN zijn. Printspoor ontbrak bij de ou= tput van de clock
generator. Condensator en FET niet aangesloten op input van de opamp doo= r ontbrekend print-
spoor. Clock output lag tussen -15V en +15V, Transistor zat niet aan gro= und door ontbrekend
printspoor.
Noise en Ringmodulator
Voedings connector had 1 pin die niet goed gesoldeerd zat. 2 Printsporen= ontbraken. Pink en
white noise zitten omgedraaid op de print. Opamp noise werkte niet, zorg= de voor hele grote
stroom. Adapter printje gemaakt naar SIL en een andere opamp gemonteerd.= Noise level te
laag. =E2=80=9CVoetje=E2=80=9D gemonteerd en transistor uitgezocht voor = beste ruis. Weerstand aangepast om versterking groter te maken.
VCO translated to German:
Pi=
n aus dem FET nicht korrekt, neuer FET montiert.
R30 fehlte, in der Dokumentation mit Modifikationen w=C3=A4re dies ein 2k2 =
Widerstand.
10K auf der Unterseite der Platine montiert.
trace unte=
rbrochen. Fehlende 820 Ohm Widerstand montiert.
R48 ist auf der Platine=
als 100k markiert, muss 10k sein.
Der Widerstand in der Impulsbreitenschaltung fehlte. 56K Widerstand statt 5=
60K
montiert. Jumper am PWM-Eingang verbinden den Eingang mit Masse. Jumper ent=
fernt.
Es gab keinen Widerstand zwischen dem Trimmer und dem Sommer der Zentralhei=
zung. 100K Widerstand montiert auf
unterer Druck. VCO 2 war aufgrund eines Problems mit dem THAT300-Transistor=
array instabil.
Transistorarray ersetzt. Ua726 bei 50 Grad nicht einstellbar, mehrere Tests=
durchgef=C3=BChrt,
Heizung kann nicht genug W=C3=A4rme erzeugen, um 50 Grad zu erreichen. Maxi=
mal 43 Grad
war im Testaufbau machbar. Auf 38 Grad eingestellt.
ht= tp://www.emcloned.com/viewtopic.php?f=3D24&t=3D283&p=3D6293&hil= it=3D702#p6293
1) The right=
side of R22 15K resistor (connected to uA726 pin 1) is tied directly to gr=
ound via the link that is physically located between IC1 (CA1458) and IC2 (=
LM301A).
2) The trace that joins pin 2 of the=
uA726, the 1K R23 resistor, D1 anode, 100K R27 and pin 3 of IC3 CA3140 doe=
s not connect to ground.
3) The "820 MF" (820=
ohm metal film, I presume) resistor that is in parallel with the 1K MF res=
istor to ground on the right side of R22 15K on the schematic is missing fr=
om both the BOM and the PCB. 1K and 820 ohm in parallel like that should ma=
ke about a 450 ohm resistance.
Assuming the s=
chematic is correct (which seems highly likely for 1 and 2 above, and reaso=
nable for 3 as well) I made corrections to my PCB to match the schematic an=
d tested again. I saw no change in behaviour (0V on the right side of the R=
22 15K). I desoldered the right left of the R22 15K resistor and it measure=
d it and it tracked the IC1A output perfectly. I resoldered it in place and=
desoldered the R23 1K and the 820 ohm resistors and measured again - still=
0V. I removed the BC547s I was using in place of a uA726 and the voltage t=
hen tracked IC1A output just fine. I resoldered the R23 1K and 820 ohm resi=
stors and it once again measured 0V. So if either the resistors, or the "uA=
726" are in place, then I do not see a voltage going in to pin 1 of uA726.<=
/span>
Just in case my understanding is incorrect I =
tried measuring the current flowing out of uA726 pin 4 (I believe the trans=
istor pair is a voltage to current converter which drives the actual oscill=
ator circuit itself?) There was no current flow in any of my test cases.
So I am stumped for now. Does anyone have any s=
uggestions? No-one has reported a successful build here or on muffs that I =
can see.
Damir, what is the status of your bu=
ilds? Do they work, and if so, did you have to make any corrections like mi=
ne?
I already know about the CV width adjustm=
ent fix on rev1 boards here: but I do not be